|
The MATRIX-2000 is
a complete sound reinforcement
solution consisting of two 12”
two-way speakers and an 18”
subwoofer, equipped with a built-in
1200-watt three-channel amplifier.
The three-channel amplifier houses
all the electronics required
to run the system including electronic
crossovers, equalization and
compressors. The electronic circuity
is fine tuned to match all of
the components for the best possible
sound.
The MATRIX-2000 is designed for easy operation, as you do not
need to tweak frequencies or finesse levels. To set-up the system’s components,
simply connect the XLR right and left signal cables, speaker cables and power
cord and you’re ready to go! |
|
|
SUGGESTED
APPLICATIONS:
Mobile
DJ * Karaoke * Nightclub, Restaurant,
Bar Install * Corporate Audio / Video
* Home Entertainment
System * Live Sound System * Stage Monitoring
System * Booth Monitoring System * Drum
Monitoring
|
Download
the Matrix 2000 Instruction Manual
|
BUILT-IN
3-CHANNEL AMPLIFIER
The
18” subwoofer enclosure
is divided into two separate
compartments. The front
chamber serves as the cabinet
for the cast-framed, 4” voice
coil, 18” subwoofer.
The rear chamber houses
all of the system’s
electronic circuitry, which
includes the amplification
for all three components,
power supply, compressor
and preamps. The 18” subwoofer
has a power handling
capability of 600 watts
and a nominal impedance
of 8 ohms. |
 |
|
|
 |
12”
TWO-WAY SPEAKERS:
The 12” two-way
speakers are loaded with B-52 custom
designed 12”
loudspeakers and 1“ titanium
diaphragm compression drivers,
mounted to 900 x 400 constant
directivity horns. The speakers
are designed to be pole mounted,
sit as stage monitors and have
built-in (3/8” – 16
TPI) flying hardware for permanent
installations. The front panel
of the two-way speakers are convex
so as to fit perfectly on to
the subwoofer’s front grille.
Each two-way speaker has the
power handling capability of
300 watts and a nominal impedance
of 4 ohms. |
|
|
TRANPORTING
THE SYSTEM:
Move
the subwoofer onto its casters
and place the included cover
over the subwoofer. Next,
pull the included covers
over the satellite speakers
and close the zippers. It
is recommended that you transport
the subwoofer and satellites
separately. You may transport
all the components at the
same time by placing the
satellite speakers onto the
subwoofer’s front panel
facing down. Secure the satellite
speakers to the subwoofer
with the included locking
strap by fastening it to
the bar handles on the side
of the subwoofer cabinet. |
 |
|
|
|
SPECIFICATIONS:
|
1200-WATT
3-CHANNEL AMPLIFIER
|
Subwoofer
Power Output:
12" Two-Way Power Output:
Line in:
Parallel out:
Input Impedance:
Speaker Out:
Power Requirement:
Crossover Frequency:
|
600
W / 8 Ohms
2 x 300 W / 4 Ohms
XLR Female
XLR Male
48 k Ohms
Speakon NL4 Style Connector
115V<>50/60Hz<>10A
230V<>50/60Hz<>5A
120 Hz; 24 dB/ Octave |
|
|
18"
SUBWOOFER
|
Speaker:
Nominal Impedance:
Subwoofer Freq. Response:
Sound Pressure Level (1w/1m):
Maximum SPL:
Weight:
Dimensions (Transport): |
1
x 18" Cast-Framed, 4" Voice Coil
Custom Subwoofer
8 Ohms
30 - 120 Hz
129 dB
130 dB
160 lbs
35" (H) x 28" (W) x 23"
(D) |
|
12'
TWO-WAY SPEAKERS
|
Speaker
Input:
Loudspeaker:
Compression Driver: HF Dispersion: Nominal
Impedance:
Active Freq. Response:
Crossover Frequency (passive):
Maximum SPL:
Weight:
Dimensions (Upright): |
Speakon
style connector
(pin 1+ = +, pin 1- = -)
12” Custom Built B-52 Transducer
1” Exit Titanium Diaphragm on Constant
Directivity Horn
90 x 40
4 Ohms
120 20K Hz
2K Hz 12 dB/Octave
126 dB
40 lbs.
23” (H) x 14” (W) x 13” (D) |
|
COMPLETE
SYSTEM
|
Weight:
Dimensions
(Transport): |
245
lbs
47”
(H) x 24” (W) x 28” (D) |
|
